Author Topic: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron  (Read 13902 times)

Etheric Zone 1111

  • Guest
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #90 on: April 11, 2020, 06:29:14 PM »
You normally don't need 50 volts.
The reason you need more volts than 10 going into your power module is so that the module has voltage available to control the current.  So if the cell resistance becomes high (like raising the cathode), the module can apply more voltage to maintain the desired current, and if the cell resistance is lower, the module can decrease the applied voltage to bring the current back to the desired level.  Current equals voltage divided by resistance.

BUT remember the 10 volts minimum is for an electrode spacing of 1.5 inches (37mm)
At 2 inches, you need 12 volts
At 3 inches, you need 16.5 volts
This is to provide the same electric field strength which propels ions from one electrode to the other.

Required volts = 4.33 X Spacing in inches plus 3.5

Higher ppm does not require higher volts.

I found these 2 items to help me build a low cost generator , all I will be making is 20ppm , using 1.5” spacing 2 10 Gauge silver Rods , would this set up work Sir?

And this will be the power source :
HP 0957-2286 Printer AC Power Supply Adapter Output 30V 333mA Transformer.

Offline wgpeters

  • Kephra's other account
  • Expert
  • Participant
  • ***
  • Posts: 634
  • Likes: 75
    • SilverTron Support
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #91 on: April 11, 2020, 07:07:16 PM »
I will be using 1.5” Spacing with my 10 Gauge Silver Rods .
I will only be making 20ppm colloidal silver .

I found a HP printer 30v 3a power supply that can provide the power for the above module , but I don’t know if 3a will be sufficient for the process.
HP 0957-2286 Printer AC Power Supply Adapter Output 30V 333mA Transformer

Ed
It is more than enough. 
A person's worth is solely determined by what he does for others.

Offline Smoke7

  • Participant
  • **
  • Posts: 51
  • Likes: 3
  • "A picture is worth 1000 words"
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #92 on: April 11, 2020, 07:13:00 PM »
Yes I was look8ng at a 50v 5ma Module to build my own power supply.

https://www.ebay.com/i/253362877198?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=253362877198&targetid=907798224154&device=t&mktype=pla&googleloc=9012276&poi=&campaignid=9338046428&mkgroupid=94993970859&rlsatarget=pla-907798224154&abcId=1139336&merchantid=118852035&gclid=CjwKCAjw1cX0BRBmEiwAy9tKHko8ptjYsioVKfDfRAzCrOvthbA539EmtaRLrM_K2UjlfLDhH1_-exoCoDQQAvD_BwE

Ed

Ed,
The module you showed me is not 5ma, it is 5AMP and it is a similar module to what I have, only more modern and 50v VS mine is 36. It will do an awesome job for the generator, however in my opinion 50V is a little bit overkill. I have never seen that somebody will use more than 30V but I may be wrong and also to get up to 50v you will have to provide 50v power supply which will be harder to find and more expensive.  I may be able to help you with the power supply, we use CISCO access points at work which has a 48v power supply. I will search E-Bay and if I find one I will send you a link.


I found this HP printer power source that could power the above module , I won’t need 50v .
HP 0957-2286 Printer AC Power Supply Adapter Output 30V 333mA Transformer


That will do it and much cheaper. I saw on E-Bay for around $8 with free shipping.
"An ounce of prevention is worth a pound of cure"

Etheric Zone 1111

  • Guest
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #93 on: April 11, 2020, 07:24:18 PM »
Awesome was waiting to receive Kehpras blessing!

Thanks All Going To Order On EBay!

Ed

Offline Smoke7

  • Participant
  • **
  • Posts: 51
  • Likes: 3
  • "A picture is worth 1000 words"
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #94 on: April 11, 2020, 09:31:57 PM »
Awesome was waiting to receive Kehpras blessing!

Thanks All Going To Order On EBay!

Ed

I want to personally thank “cfinisbet” (sorry I do not know your name) for creating this thread and really helping us out. THANK YOU.

You are welcome.
« Last Edit: April 12, 2020, 06:57:38 PM by cfnisbet »
"An ounce of prevention is worth a pound of cure"

Etheric Zone 1111

  • Guest
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #95 on: April 11, 2020, 09:46:45 PM »
Just ordered everything even a vented project box!

Ed

Offline imcool

  • Participant
  • **
  • Posts: 219
  • Likes: 4
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #96 on: April 11, 2020, 10:55:54 PM »
Just ordered everything even a vented project box!

Ed
Are ebay sellers from USA are working? or you ordered from a seller who is based in China?

Etheric Zone 1111

  • Guest
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #97 on: April 11, 2020, 10:57:19 PM »
US...

Offline Smoke7

  • Participant
  • **
  • Posts: 51
  • Likes: 3
  • "A picture is worth 1000 words"
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #98 on: April 12, 2020, 11:14:37 PM »
FYI.
A couple of days ago I was reading some of the previous posts on here and found one article about the distilled water posted by someone (didn’t memorize his name). He was saying that Wal-Mart distilled water has a 000PPM, so I went to my local Wal-Mart and bought 4 one-gallon jugs of water and tested them with a TDS meter (yes I know we can’t measure silver with TDS) and all 4 jars showed 005PPM in it. I am not sure if it was a bad batch or what? I went to Menards and purchased 1 gallon of water for the test and its result was 000PPM.
I just wanted to share this with you.
« Last Edit: April 13, 2020, 02:38:30 AM by Smoke7 »
"An ounce of prevention is worth a pound of cure"

Offline imcool

  • Participant
  • **
  • Posts: 219
  • Likes: 4
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #99 on: April 13, 2020, 09:50:24 PM »
thats why I make my own distilled water,

Offline Smoke7

  • Participant
  • **
  • Posts: 51
  • Likes: 3
  • "A picture is worth 1000 words"
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #100 on: April 14, 2020, 01:10:43 AM »
thats why I make my own distilled water,
That is awesome.
I was going to make my own water distiller, but I only make colloidal silver once a year and have no other need for distilled water, so it’s just going to be sitting around the house taking up space.
"An ounce of prevention is worth a pound of cure"

Offline imcool

  • Participant
  • **
  • Posts: 219
  • Likes: 4
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #101 on: April 14, 2020, 01:35:17 AM »
thats why I make my own distilled water,
That is awesome.
I was going to make my own water distiller, but I only make colloidal silver once a year and have no other need for distilled water, so it’s just going to be sitting around the house taking up space.
yes but I want to make gold water on regular basis too so i need distilled water

Offline Smoke7

  • Participant
  • **
  • Posts: 51
  • Likes: 3
  • "A picture is worth 1000 words"
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #102 on: April 14, 2020, 06:25:33 AM »
thats why I make my own distilled water,
That is awesome.
I was going to make my own water distiller, but I only make colloidal silver once a year and have no other need for distilled water, so it’s just going to be sitting around the house taking up space.
yes but I want to make gold water on regular basis too so i need distilled water
Lucky you, in my house only one person has GOLD: my wife. :)
"An ounce of prevention is worth a pound of cure"

Offline Smoke7

  • Participant
  • **
  • Posts: 51
  • Likes: 3
  • "A picture is worth 1000 words"
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #103 on: April 14, 2020, 09:50:08 PM »
One simple question.
Do I have to rinse all the bottles, containers, and glass with the distilled water to store the colloidal silver or it's only required when you are making colloidal silver?
Thank you.

I would say rinse out with Distilled Water before making it, and rinse out your storage bottles before using them.
« Last Edit: June 08, 2020, 08:59:16 PM by cfnisbet »
"An ounce of prevention is worth a pound of cure"

Etheric Zone 1111

  • Guest
Re: HOW TO MAKE COLLOIDAL SILVER if you can't get a SilverTron
« Reply #104 on: April 15, 2020, 12:52:07 AM »
Yes I was look8ng at a 50v 5ma Module to build my own power supply.

https://www.ebay.com/i/253362877198?chn=ps&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&itemid=253362877198&targetid=907798224154&device=t&mktype=pla&googleloc=9012276&poi=&campaignid=9338046428&mkgroupid=94993970859&rlsatarget=pla-907798224154&abcId=1139336&merchantid=118852035&gclid=CjwKCAjw1cX0BRBmEiwAy9tKHko8ptjYsioVKfDfRAzCrOvthbA539EmtaRLrM_K2UjlfLDhH1_-exoCoDQQAvD_BwE

Ed

Ed,
The module you showed me is not 5ma, it is 5AMP and it is a similar module to what I have, only more modern and 50v VS mine is 36. It will do an awesome job for the generator, however in my opinion 50V is a little bit overkill. I have never seen that somebody will use more than 30V but I may be wrong and also to get up to 50v you will have to provide 50v power supply which will be harder to find and more expensive.  I may be able to help you with the power supply, we use CISCO access points at work which has a 48v power supply. I will search E-Bay and if I find one I will send you a link.


Can you please tell me the difference of 5ma, and 5AMP , And would I be able to set that module at 5ma?
Sorry  electronics is not my strong hold ..
Ed

So I would have to set the Amps At 0.0005A on the module ?