Author Topic: Why cell voltage above 10 volts?  (Read 136 times)

Offline axkman

  • Participant
  • **
  • Posts: 36
  • Likes: 0
Why cell voltage above 10 volts?
« on: August 22, 2020, 06:19:03 PM »
Hi there!

I read here on the forum that it was advised to keep the cell voltage above 10 volts, but my question: why does the cell voltage needs to be above 10 volts?

Thank you!
« Last Edit: August 22, 2020, 08:54:42 PM by axkman »

Offline Gene

  • Expert
  • Participant
  • ***
  • Posts: 1160
  • Likes: 84
Re: Why cell voltage above 10 volts?
« Reply #1 on: August 23, 2020, 02:33:41 AM »
You're running an electroplating cell thats designed to fail for using the electrolyte we use.

In a functioning plating cell the silver ions would be pulled into solution and then deposited on the cathode (a.k.a. plating). The electrolyte we use inhibits this plating action from happening but it serves a couple other purposes - reducing the resistance of water which is nearly a perfect insulator so you can get milliamps of current through it and raising the PH to around 8-8.5 so that the reducer works as they only reduce in alkaline environments.

There's chemistry involved, zeta potential,... as to why you want 10V minimum. A little higher (I usually process around 12V) is even better.  Higher is even better.

As I recall, this was a question that was answered on the forum in the past though the search facility being as stellar as it is, good luck finding it.

Offline axkman

  • Participant
  • **
  • Posts: 36
  • Likes: 0
Re: Why cell voltage above 10 volts?
« Reply #2 on: August 23, 2020, 12:01:20 PM »
Thank you for your reply. Hugely appreciated, as always.

I'm browsing thru the search engine. There is a lot of search results as to 10v cell voltage and that some people wrote "kephra said so" (and I know he knows what he's doing!) but haven't found a conclusive post why the cell voltage needs to be at 10v.
Electrodissolution (process of the silver being pulled away from anode into solution) happens at lower voltage than 10v aswell. And the rate of silver ions pulled away from anode into solution is depending on the current that flows from one electrode to the other thru the (distilled water + electrolyte) solution. So I still kind of wonder why that is said need to be at cell voltage of 10v or higher.


Offline Gene

  • Expert
  • Participant
  • ***
  • Posts: 1160
  • Likes: 84
Re: Why cell voltage above 10 volts?
« Reply #3 on: August 23, 2020, 07:58:06 PM »
Here's Kephra's explanation.

Its a good read but his take on the voltage thing is in the Electrolyte section of his post.

https://www.cgcsforum.org/index.php?topic=1143.msg8849#msg8849


Offline axkman

  • Participant
  • **
  • Posts: 36
  • Likes: 0
Re: Why cell voltage above 10 volts?
« Reply #4 on: August 23, 2020, 11:47:38 PM »
Thanks man!

Nicely detailed explained, appreciated!

Offline ESTACIONSJ

  • Participant
  • **
  • Posts: 8
  • Likes: 0
Re: Why cell voltage above 10 volts?
« Reply #5 on: Yesterday at 04:41:09 AM »
so i have a question, so i have a power supply that has a constant current setting, so if i set my constant current at  say 12 volts and the amps at 15ma because im using a silver 1oz bar i should be good...

Offline cfnisbet

  • Administrator
  • Participant
  • *****
  • Posts: 2016
  • Likes: 115
Re: Why cell voltage above 10 volts?
« Reply #6 on: Yesterday at 09:01:16 AM »
so i have a question, so i have a power supply that has a constant current setting, so if i set my constant current at  say 12 volts and the amps at 15ma because im using a silver 1oz bar i should be good...
No, you can't do that. You can only set the current or the voltage to be constant. In your case, you would set the constant current to be 15mA and allow the voltage to drift. Then you adjust the amount of cathode in the water (minimise it) to keep the voltage above 10 volts (ideally higher).

"constant current at  say 12 volts" - is incorrect; volts is voltage, so that would be constant voltage, which you don't want to do.

Offline ESTACIONSJ

  • Participant
  • **
  • Posts: 8
  • Likes: 0
Re: Why cell voltage above 10 volts?
« Reply #7 on: Yesterday at 11:43:10 PM »
okay thank u for the info, if u say to keep the voltage above 10 volts (ideally higher). whats the highest Volts u would want it to be.

Offline Gene

  • Expert
  • Participant
  • ***
  • Posts: 1160
  • Likes: 84
Re: Why cell voltage above 10 volts?
« Reply #8 on: Today at 02:54:41 AM »
Higher is better BUT given the resistivity of your cell due to the electrolyte, you're going to get to a point where you can't go any higher because the cathode has come out of the water. There are limits.  You're just going to have to play around to see what those limits are at 15ma.

The thing is though, you don't want the cathode so close to being out of the water that evaporation or a little mechanical vibration disconnects it from the cell because then you'll have absolutely no idea what you actually made as far as PPM.

We use a thin 24 AWG (american wire gage which is a standard) length of copper wire.  The trick with the cathode is to minimize the surface area in the water.  For a thick wire, that means just glancing the surface which isn't such a good idea.  For a thin wire like this, for sure you'll still have a good half inch in the water when you're up around or over 12V. 12-15V is good. You don't really have to try to get any higher.  If you're stirring though you may be able to because stirring causes the electrical path from the anode to cathode through the water to get longer (an arc is longer than a straight line, right?) but don't push it too far.  If its good enough, its good enough!  Words to live by. "Perfection" is not required - just good enough (wink).

As far as the power supply, does it have constant current and constant voltage settings? If so, I'd doubt you can use both at the same time.  If its a current "limiter", thats different.  Thats usually there for protection so if whatever you're powering shorts out, your power supply doesn't smoke or die.

What you want to do is set the voltage high (say 20+V if you can) and adjust the current limit just measuring the current across the supply with a voltmeter to get 15ma.  BIG WARNING. For a power supply, I'm sure the current limit can be set to several amps at least.  TURN THE CURRENT LIMIT TO ITS MINIMUM SETTING (lowest current) setting BEFORE connecting the voltmeter or you may well blow it out.  Then gently adjust it to get where you want. Given your cell will be 12-15V, if the supply is outputting 20-24V, there's no way, unless the cathode comes out of the water, that the current won't remain constant at 15ma.

Let us know how you make out.

Oh, and if you manage to damage your voltmeter on a current scale, don't toss it. They ALL have an internal fuse or two you can replace and chances are good you sent it to that big fuse round-up in the sky. Some meters even have a spare fuse hidden inside but usually these are the more expensive ones. Just get a replacement fuse with the exact same rating and you're good.

Offline ESTACIONSJ

  • Participant
  • **
  • Posts: 8
  • Likes: 0
Re: Why cell voltage above 10 volts?
« Reply #9 on: Today at 05:49:09 AM »
thanks for the advice, made my first batch quick in 50 minutes. With my new set up and ure guys advice
here are some pictures.

1 litres DW x 50 ppm x 15   =   50 minutes   
                  15 mA

20 drops of electrolyte and 20 drops of reducer (karo syrup mix), then silver cleaned after with butane torch

thanks for the advice, made my first batch quick in 50 minutes. With my new set up and ure guys advice
here are some pictures.




<img src="https://i.imgur.com/tFKhUoq.jpg" title="source: imgur.com" />
« Last Edit: Today at 06:00:21 AM by ESTACIONSJ »